This 8 Way RJ45 Patch Panel is used to terminate 8 Cat5e cables. an 8 Way Adapter plate will be required to fit this into the enclosure.
(An 8 Way Adapter plate will be required to fit this panel. - PNL-ADP-8-01)

This 12 Way RJ45 Patch Panel is used to terminate 12 Cat5e cables

This modular patch panel allows the use of a range of modules providing Cat5e UTP, Cat5e FTP, Cat6 UTP, Cat6 FTP, F Coax, BNC and Fibre terminations. These modules can be mixed and matched in the same panel if required. Additionally modules can be rearranged after termination without the need to reterminate the cables.
8 modules can be used on this full width patch panel.

Click here for a choice of modules to fit into this patch panel More Modules for this Modular patch panel

This patch panel is used as a 2 x 4 jack telephone bus. A single Cat5e cable from each incoming telephone service is connected to the back by IDC and the telephone service is then available from 4 of the RJ45s on the front for patching to other patch panels. Two telephone lines can be connected to this patch panel providing 4 RJ45s on the front for each telephone line.

Additionally there is an auxiliary IDC on the back for each bus. These can be connected together to create a single 8 port telephone bus. Alternatively, Sky dial up service can be connected to this IDC to prevent the user accidentally disconnecting it from the front when repatching the system.

(An 8 Way Adapter plate will be required to fit this panel. - PNL-ADP-8-01)

This patch panel offers 12 Gold Plated Banana Jacks on the front of the panel. On the rear of the panel is screw down terminal blocks for simple termination of the speaker cable.

This panel provides a professional mechanism for termination of speaker cable for use with a muti room audio system. One panel can terminate 3 speaker pairs worth of cable.

An 8 Way Adapter plate will be required with this panel.

This patch panel offers 20 Gold Plated Banana Jacks on the front of the panel. On the rear of the panel is screw down terminal blocks for simple termination of the speaker cable.

This panel provides a professional mechanism for termination of speaker cable for use with a muti room audio system. One panel can terminate 5 speaker pairs worth of cable.

This panel has a brushed opening to allow cables to pass from the back of the mounting plate to the front in a tidy manner.

This panel will require an 8 Way Adapter plate to fit into the enclosure.

This panel has a brushed opening to allow cables to pass from the back of the mounting plate to the front in a tidy manner.

This patch panel has 12 x back to back F couplers fitted. This allows clean termination of Coax cables. A label strip is provided. An 8 Way Adapter plate will be required to fit this into the enclosure.

This patch panel has 20 x back to back F couplers fitted. This allows clean termination of Coax cables. A label strip is provided.

The RCA Phono Panel is normally used to terminate line level cable but can be used to terimate speaker cable. The 6 pair panel can terminate 6 pairs of audio cable. The termination on the back of the panel is via screw down terminal blocks. The front presentation is via RCA Phono Jacks.

An 8 Way Adapater Plate will be required to fit this patch panel.

This patch panel offers 20 RCA Phono Jacks on the front of the panel. On the rear of the panel are screw down terminal blocks for simple termination of the cable.

This panel provides a professional mechanism for termination of audio cable. One panel can terminate 10 audio pairs worth of cable.

This adapter plate allows a 1U 8 Way patch panel to fit into the unit. It can be fitted to the 8 Way patch panel to extend it to the full width of cabinet (i.e. adapts it to a 12 way size). This can be used with the 8 way Telephone Bus panel or an 8 way RJ45 patch panel.

This adapter plate allows 2 x 1U 8 Way patch panel or a 2U 8 way unit to fit into the unit. It can be fitted to the 8 Way patch panels to extend them to the full width of cabinet (i.e. adapts to a 12 way size). This can be used with the 2 x 8 way Telephone Bus panel or 2 x 8 way RJ45 patch panel or with one of the ABUS Audio panels.

This adapter plate allows 3 x 1U 8 Way patch panel or a 2U 8 way unit and a 1U 8 Way Patch Panel to fit into the unit. It can be fitted to the 8 Way patch panels to extend them to the full width of cabinet (i.e. adapts to a 12 way size). This can be used with the 1 x 1U 8 way Telephone Bus panel and the 2U ABUS Audio panels.

This adapter plate allows 4 x 1U 8 Way patch panel or a 2 x 2U 8 way unit to fit into the enclosure. It can be fitted to the 8 Way patch panels to extend them to the full width of cabinet (i.e. adapts to a 12 way size). This can be used with 2 x 2U ABUS Audio panels allowing for 8 zones of audio.

This adapter plate allows 5 x 1U 8 Way patch panel or 2 x 2U 8 way units and a 1U 8 Way Patch Panel to fit into the enclosure. It can be fitted to the 8 Way patch panels to extend them to the full width of cabinet (i.e. adapts to a 12 way size). This can be used with the 1 x 1U 8 way Telephone Bus panel and 2 x 2U ABUS Audio panels allowing for 8 zones of audio and the telephone bus.

This 1U blanking plate is used to fill unused slots in the cabinet.

This 2U blanking plate is used to fill unused slots in the cabinet.

This 3U blanking plate is used to fill unused slots in the cabinet.

This 4U blanking plate is used to fill unused slots in the cabinet.

The blank panel is the same size as an 8 way patch panel and used to fill empty slots.

A Master Voice Adapter converts from an RJ45 socket to a BT LJU socket. The master contains the ringing circuit and the surge protector. This is only used if the property does not have a BT Master elsewhere in the property. Only one master is required per property.

The Secondary Voice Adapter simply converts from an RJ45 socket to a BT LJU socket. It is used when there is a Master at the point in the property where the incoming telephone line enters. This is the typical voice adapter used.

The PBX Master Voice Adapter converts an RJ45 socket into a BT LJU socket and contains the ringing circuit. It is used where a PBX telephone system is installed in the property.

The unit has 4 RJ45 sockets for audio outputs (i.e. 4 zones) and an RJ45 audio input and an expansion output if you want to hang a second hub off this hub to provide 8 zones.

An ABK-50 is required at the audio source to convert the unblanced line level audio source to balanced line level and connect to a Cat5e cable. Cat5e connections can be on a seperate patch panels and patched across using patch leads or the incoming Cat5e cables can come through the brush opening to the right of the panel to save on patch panel ports.

A power supply is included and is fed through the brush opening to connect to the DC power socket on the front.

This panel is 2U and 8 Way siized. A 2U 8 Way adapter plate is required to fit this panel.

This A-BUS audio hub has 8 RJ45 sockets for audio outputs. These are split into 2 banks of 4. The top roll are A and the lower sockets are B. This gives you 4 zones and 4 subzones. i.e. 1A and B, 2 A and B, 3 A and B and 4 A and B. Also 4 RJ45 audio inputs and an expansion output is provided if you want to hang a second hub off this hub to provide a further 4 zones and subzones.

Four ABK-50s are required at the audio sources to convert the unbalanced line level audio sources to balanced line level and connect to the Cat5e cables. Cat5e connections can be on a seperate patch panels and patched across using patch leads or the incoming Cat5e cables can come through the brush opening to the right of the panel to save on patch panel ports.

A power supply is included and is fed through the brush opening to connect to the DC power socket on the front.

A second power supply must be purchased if any of the B outputs are used.

This panel is 2U 8 Way sized and requires a 2U 8 Way adapter plate.

This hub is used in conjunction with the A-BUS Multi Source Audio Hub in order to expand the system. This hub adds an additional 4 zones and 4 subzones.

Two Cat5 epatch leads are used to connect to the first hub and is supplied with a power supply.

This cabinet is designed to surface mount onto a wall. The unit is 95mm deep. It is screwed to the wall from screw fixings in the back. The top and bottom ends can be removed whilst the unit is fitted to ease installation. The top and bottom panels have knock outs that can be used if truncking is being used to bring the cabling to the enclosure. There are also large knock outs in the back to allow for cable entry from the back of the unit.

Outter Dimensions - H320xW320xD95mm
Internal Capacity - 5U

Includes Lock and Key

This cabinet is designed to surface mount onto a wall. The unit is 95mm deep. It is screwed to the wall from screw fixings in the back. The top and bottom ends can be removed whilst the unit is fitted to ease installation. The top and bottom panels have knock outs that can be used if truncking is being used to bring the cabling to the enclosure. There are also large knock outs in the back to allow for cable entry from the back of the unit.

Outter Dimensions - H452xW315xD95mm
Internal Capacity - 8U

Includes Lock and Key

This cabinet is designed to surface mount onto a wall. The unit is 95mm deep. It is screwed to the wall from screw fixings in the back. The top and bottom ends can be removed whilst the unit is fitted to ease installation. The top and bottom panels have knock outs that can be used if truncking is being used to bring the cabling to the enclosure. There are also large knock outs in the back to allow for cable entry from the back of the unit.

Outter Dimensions - H570xW315xD95mm
Internal Capacity - 11U

Includes Lock and Key

This cabinet is designed to flush mount into a stud partition wall. The unit is 95mm deep. It has dog leg grips on the left and right to achieve a firm fixing. Cable access is via top and bottom or from the back. The top and bottom ends can be removed whilst the unit is fitted to ease installation. The back has a large knock out.

Outter Dimensions - H320xW320xD95mm
Cut Out Dimensions - H305xW293mm
Internal Capacity - 5U

Includes Lock and Key

This cabinet is designed to flush mount into a stud partition wall. The unit is 95mm deep. It has dog leg grips on the left and right to achieve a firm fixing. Cable access is via top and bottom or from the back. The top and bottom ends can be removed whilst the unit is fitted to ease installation. The back has a large knock out.

Outter Dimensions - H452xW315xD95mm
Cut Out Dimensions - H428xW293mm
Internal Capacity - 8U

Includes Lock and Key

This cabinet is designed to flush mount into a stud partition wall. The unit is 95mm deep. It has dog leg grips on the left and right to achieve a firm fixing. Cable access is via top and bottom or from the back. The top and bottom ends can be removed whilst the unit is fitted to ease installation. The back has a large knock out.

Outter Dimensions - H570xW315xD95mm
Cut Out Dimensions - H557xW293mm
Internal Capacity - 11U

Includes Lock and Key

The 8 Way Extender Amplifier can be connected the main TV Amplifier to add additional TV Outlets to the system. One Amp Adder is required per TV Extender Amplifer.
This item is specifically designed for mounting into 'Home Network Panels' and other enclosures.

The 16 Way Extender Amplifier can be connected the main TV Amplifier to add additional TV Outlets to the system. One Amp Adder is required per TV Extender Amplifer.
This item is specifically designed for mounting into 'Home Network Panels' and other enclosures.

This TV amplifier has inputs for Sky, TV, FM, DAB and a spare for CCTV. The unit requires a Lounge Wall Plate to pick up the signal from the Sky box which is then fed back into the return loop on the TV amp. 4 Outputs are then provided.

The TV amplifier fits to the backplane of the enclosure.

This TV amplifier has inputs for Sky, TV, FM, DAB and a spare for CCTV. The unit requires a Lounge Wall Plate to pick up the signal from the Sky box which is then fed back into the return loop on the TV amp. 8 Outputs are then provided.

The TV amplifier fits to the backplane of the enclosure.

The TV Extender Mounting Spacers are used to mount the TV Extender Amplier on top of the main TV Amplifier.

This fully screened outlet plate is designed for domestic installations consisting of VHF,TV & SKY. The plate has a triplexed output, UHF - FM/DAB - SAT.

It also has a 2nd SAT socket for use with SKYplus. (Run another cable from the sky dish to this plate to use this socket).

It also has a modular BT phone socket. In addition there is a spare modular slot which can take the Co-ax socket Return module (run another cable from this socket back up to your panel mounted Distribution Amplifier).

Double Gang outlet plate finished in white plastic. All ports are marked up.
(Note: This product is compatible with the Aldous Systems Home Network System)