This single source system will distribute the audio from a single device such as an iPod or Sky set top box to 4 rooms. Each room has a discrete in wall volume control which drives a pair of ceiling high quality ceiling speakers. The system is centrally powered by a single power pack. Only a single run of low cost Cat5e cable is required to each keypad from the central hub making this very easy and cost effective to install.

Kit includes:-
1 x AB-62 - Single Source Hub
1 x APS-40 - Power Supply
4 x ABE-10 - Infra Red Emmiters
4 x ABO-20 - Power Module Keypads
4 x ABP-C6 - 6 1/2 inch celing speakers
4 x AS-CRI-40 - American Style Back Boxes
right click for info sheet . . .

This system provides the same solution as above but instead of a rotary knob volume control, a push button volume control is provided in the keypad. An up button turns on the keypad and allows increase of volume and the down button turns off the zone and allows volume down adjustment. Additionally, each keypad is supplied with a mini Infra Red remote control so that the off/on and volume can be adjusted without having to physically touch the keypad. Also, the keypad can accept Infra Red Commands destined for the music source and the Infra Red Command can then be retransmitted using an Infra Red Emitter at the hub. Therefore, if you have the remote control for the source equipment then you can control the source equipment even though you are in a different room.

Kit includes:-
1 x AB-62 - Single Source Hub
1 x APS-40 - Power Supply
4 x ABE-10 - Infra Red Emmiters
4 x ABO-42B - Infra Red Power Module Keypads
4 x ABP-C6 - 6 1/2 inch celing speakers
4 x AS-CRI-40 - American Style Back Boxes
right click for info sheet . . .

This system provides the same as above but includes a more sophisticated central hub and keypad. This system allows you to connect up to 4 different bits of source equipment to the main hub (i.e. iPod, Sky set top box, Radio, CD Player) and from the keypad, each room can decide which of the 4 sources is to be played. Each room can select the source independently of the next room so you can have 4 different rooms playing different source simultaneously or they can all be playing the same thing or any combination thereof. Again, each keypad can be controlled remotely and the system will pass Infra Red commands to control the source equipment using the source equipment remote control.

Kit includes:-
1 x ABX-88 - Multi Source Hub
1 x APS-40 - Power Supply
4 x ABE-10 - Infra Red Emmiters
4 x ABO-45 - Power Module Keypads
4 x ABP-C6 - 6 1/2 inch celing speakers
4 x AS-CRI-40 - American Style Back Boxes
right click for info sheet . . .

This kit provides the AB-62 4 zone single source hub with the A-BUS/DIRECT speakers. These speakers have the amplifier fitted to the right speaker. There is no keypad with this solution. The Cat5e cable from the hub connects to the right speaker. The speaker has an IR receiver built in for control of the speaker and control of the source equipment.

Kit includes:-
1 x AB-62 - Single Source Hub
1 x APS-40 - Power Supply
4 x ABE-10 - Infra Red Emmiters
4 x ABD-C6 - 6 1/2 inch A-BUS/DIRECT Active celing speakers
right click for info sheet . . .

This kit uses the A-BUS/DIRECT speakers to provide high quality amplified audio. No keypad is required as the amplifier is fitted in the right speaker. Therefore the Cat5e cable from the hub runs all the way to the right speaker. The IR receiver in the speaker allows control of the speaker for volume and source selection. Each pair of speakers comes with the mini remote control.

Kit includes:-
1 x ABX-88 - Multi Source Hub
1 x APS-40 - Power Supply
4 x ABE-10 - Infra Red Emmiters
4 x ABD-C6 - 6 1/2 inch A-BUS/DIRECT Active celing speakers
right click for info sheet . . .

Kit includes:
1 x AB-61 - 2 zone single source system
1 x ABD-C6 - A-BUS Direct Speakers
1 x AO314 - iPod in Wall Docking Station (ipod not included)
3 x AS-U-C5E-P44-GRY-30 - Patch Leads
2 x AS-CRI-40-1 - American Back Box
1 x WPO-10 - American Faceplate
1 x AS-LEAD-2P-2P-0.5 - 2 Phono to 2 Phono 0.5m
right click for info sheet . . .

Kit includes:
1 x AB-62 - 4 zone single source system
4 x ABD-C6 - A-BUS Direct Speakers
1 x AO314 - iPod in Wall Docking Station (ipod not included)
5 x AS-U-C5E-P44-GRY-30 - Patch Leads
2 x AS-CRI-40-1 - American Back Box
1 x WPO-10 - American Faceplate
1 x AS-LEAD-2P-2P-0.5 - 2 Phono to 2 Phono 0.5m
right click for info sheet . . .

Includes:
1 x AB-62
4 x ABD-C6
1 x AO314 (ipod not included)
1 x AB-313
4 x AS-U-C5E-P44-GRY-30
2 x WPO-10
3 x AS-CRI-40-1
1 x AS-LEAD-2P-2P-0.5
1 x AS-U-C5E-P44-GRY-10
1 x AS-U-C5E-P44-GRY-20
right click for info sheet . . .

Kit includes:
1 x ABX-88
4 x ABD-C6
1 x AO314 (ipod not included)
2 x AS-CRI-40-1
4 x ABE-10
1 x WPO-10
5 x AS-U-C5E-P44-GRY
1 x AS-LEAD-2P-2P-0.5
right click for info sheet . . .

Standard in-wall power module.
Rotary knob volume control
Cat5 110 colour coded punch down
Single gang screwless wall plate

Infra-red in-wall power module.
Rotary knob volume control
Infra red relay and status indication
Cat5 110 colour coded punch down
Single gang screwless wall plate

Infra-red in-wall power module.
Touch button volume control
Infra red and remote control level adjustment
Cat5 110 colour coded punch down
Single gang screwless wall plate
1 x ABO-40RC credit card remote
included remote controller

Multi-source in-wall power module.
Touch button volume control up/down
4-source selection left/right.
Local OFF / all OFF
Infra-red
Backlit volume level and source input indication
Cat5 110 colour coded punch down
Single gang screwless wall plate
1 x ABO-40RC credit card remote
included remote controller

Multi-source in-wall power module.
Touch button volume control up/down
4-source selection left/right.
Local OFF / all OFF
Infra-red
Backlit volume level and source input indication
RJ45 Socket for Cat5e Connection
Single gang screwless wall plate
1 x ABO-40RC credit card remote
included remote controller

Single-input interface & 2-room hub (RCA inputs)
Surface mount, single source.
Two-room hub with infra red outputs and status.
Will power up by either auto music sensing or voltage trigger from status input.
1 x APS-40 Power supply.

Single-input interface & 4-room hub (RCA inputs)
Surface mount, single source interface with four-room A-BUS RJ-45 outputs, audio inputs, infra red outputs, expansion ports and status.
Will power up the system by either auto music sensing or voltage trigger from status input.
1 x APS-40 Power supply.

Dual input interface & 8-room hub (RCA inputs)
Surface mount, dual-RCA source interface with 8-room. A-BUS RJ-45 ourputs.
Of the two source inputs one is sensed and one is the default.
Includes infra red outputs, expansion port and status. Terminal for local infra red input. One APS-40 powers four rooms. Includes input level and time delay adjustment of sensed input, auto music sensing and 12DC main amplifier status sensing for system power.
1x APS-40 power supply

4-room hub surface mount
4 room punchdown distribution hub with expansion port
For structured wiring panel
Metal plate with standoffs
1 x APS-40 power supply

4-input, 4-zone switching hub (A-BUS/Ready Inputs)
Surface-mount hub with four stereo inputs (RCA) with four dual-zone A-BUS (RJ-45) outputs (A & B each).
Expansion output to either main system amplifier or additional ABX-88
Input level adjustment, routed emitter ports, common IR output, 12 volt trigger, system status and talkback LED’s.
1 x APS-40 power supply
1 x ABO-41RC A-BUS, programable remote
right click for Installation manual. . .

This multi source hub allows the sources to be remote from the hub. There are 4 x RJ45 inputs for the sources. An ABK-50 or ABK-50-MOD must be used to connect the source to this hub. The IR outputs are on the ABK-50. This hub can drive 4 zones with 2 pairs of speakers per zone.

For additional zones use the ABX-90 as an expansion hub and connect it to this hub via 2 x Cat5e.

Supplied with 1 power supply. A second power supply is required if any of the B outputs are to be used.

This hubs is used as a zone expansion hub from the ABX-89. It connects to the ABX-89 via 2 x Cat5e cables and provides an additional 4 zones with 2 pairs of speakers in each zone.

This hub is supplied with a power supply. A second power supply is required if any of the B outputs are used.

Single input interface - surface mount
Takes audio input (RCA) and converts to A-BUS output (RJ-45).
Enables standard receivers to connect via single cat5 to structured wiring
Powers by automatic music sensing or voltage trigger from status input.

Local Input Module (LIM) in-wall
Enables input of local signal source located in the zone
Automatic signal switching
RCA inputs
Cat5 110 colour coded punch down
Single gang screwless wall plate

Single input interface - 50x50 Module
Takes audio input (RCA) and converts to A-BUS output (RJ-45).
Enables standard sources to connect via single Cat5 to a remote hub
Powers by automatic music sensing
2 x IR Emitter Outputs
Status LED
IR Talkback LED
Use with AB-62, AB-663 or Home Networking System A-BUS hubs
Fits Single gang faceplate; '1G Grid fll module' (Ref: 304201)

Single input interface - 50x50 Module
Takes audio input (RCA) and converts to A-BUS output (RJ-45).
Enables standard sources to connect via single Cat5 to a remote hub
Powers by automatic music sensing
2 x IR Emitter Outputs
Status LED
IR Talkback LED
Use with AB-62, AB-663 or Home Networking System A-BUS hubs
Fits Single gang faceplate; '1G Grid fll module' (Ref: 304201)

Local Input Module (LIM) in-wall
Enables input of local signal source located in the zone
Automatic signal switching
RCA inputs
RJ45 Connection for In and Out
Snaps into single gang faceplate with 50x50 hole
Requires 47mm deep back box

Local Input Module (LIM) in-wall
Enables input of local signal source located in the zone
Automatic signal switching
RCA inputs
RJ45 Connection for In and Out
Snaps into single gang faceplate with 50x50 hole
Requires 47mm deep back box

Mini remote control
Provides commands for volume up/down and source select
Supplied with ABO-42, ABO-45 and ABS-40

A-BUS programmable remote control
Learning remote control with A-BUS controls & memory
6-bank A-BUS remote handset with code library, learning & macro capability (including bank buttons).
Features separate A-BUS bank.

Supplied with A-BUS/DIRECT speakers
2 in 1 Handheld remote and on-wall keypad
Remote can be magnetically attached to metal surfaces
Coloured Buttons: Red, Green, Blue, Yellow
Control Buttons: Stop, Play, Repeat, +Up, -Down
Mode Buttons: Sources 1-4
Battery: 2 x 3vDL2032
Size: 57 x 91x 6.9mm (WHD)

Single infra red mini emitter
Low profile emitter in infra red translucent Lexen plastic.
3ft low profile 28 gauge cable from head and 7' 24 gauge to 3.5mm plug.
1 x blanking cover
4 x spare double sided tape labels and stick tack.

Double headed infra red mini emitter
Two low profile emitter in infra red translucent Lexen plastic.
3ft low profile 28 gauge cable from head and 7' 24 gauge to 3.5mm plug.
1 x blanking cover
4 x spare double sided tape labels and stick tack.

4A Power Supply
4 amp (96 watt)
Powers up to four A-BUS power modules
Supplied with A-BUS distribution hubs

To suit American style outlet plates

(eg: 'A-BUS' Home entertainment keypads and
other similar style home music distribution products)
71x58x96mm (DxWxH)

This single gang plastic American back box provides dog legs to grip plasterboard walls. This is ideal for stud walls.

71x57x95mm (DxWxH) approx.

This double gang plastic American back box provides dog legs to grip plasterboard walls. This is ideal for stud walls.

71x100x95mm (DxWxH) approx.

This treble gang plastic American back box provides dog legs to grip plasterboard walls. This is ideal for stud walls.

95x151x95mm (DxWxH) Approx.

This blank will blank off a single gang American back box.

This blank will blank off a double gang American back box.

This speaker pair provides an active and a passive speaker. The active speaker has an RJ45 conector on the back of the speaker. This allows connection directly to the A-BUS hub using Cat5e cable. No keypad is required. The high quality amplifier is attached to the back of the right speaker.

The right speaker also has an IR receiver to allow control of the speaker and pass thru to control the sources. An ABO-40RC remote control is provided with the speaker.

Speaker cable is then used to connect the right speaker to the left speaker.

The active speaker has an RJ45 conector on the back of the speaker. This allows connection directly to the A-BUS hub using Cat5e cable. No keypad is required. The high quality amplifier is attached to the back of the speaker.

The speaker also has an IR receiver to allow control of the speaker and pass thru to control the sources. An ABO-40RC remote control is provided with the speaker.

This part number only provides one speaker which can be used in as a simgle point speaker for rooms where there is not enought space to have a pair of speakers. There is a switch on the back which should be set to mono in this application.

This high spec ceiling speaker is an ideal compliment to any A-BUS system. This speaker pair is used with the A-BUS keypads. They are passive speakers so they need the amplifier in the keypad. If you are not using the keypad then use the active speakers ABD-C6.

Speaker Type: In-ceiling, 2 way
Woofer: 6 1/2" polypropylene
Tweeter: 3/4" mylar
Power: 5 - 60 watts
Impedance: 8 ohm
Frequency Response: 55 - 20k Hz.
Sensitivity: 88 dB
Grill: Micromesh
Finish dimensions: 9 1/2" diameter, 3" deep
Cutout dimensions: 8 1/8" diameter

With its half bridge wave design, the AC640 looks as good as it sounds.
The larger 6.5 woofer of the AC640 provides fuller low end sound.

Applications
The AC640 can be used for the following applications
2 channel audio
Multi-room audio
Home Theater rear channels
Pools, spas, hot tubs rooms, etc.
Outdoor audio (no extended contact with water)

Supplied with white grill covers.

AC642 Single Point Stereo In-ceiling Speaker
Often called dual voice coil, The AC642 single point stereo speaker provides stereo sound from a single speaker. The crossover on the rear of the speaker accepts both left and right speaker wire and the two tweeters on the bridge provide left and right output. Dual +/- 3 dB switches allows installers to increase or decrease the output of the tweeters, which comes in handy when you are setting up the room.

Applications
The AC642 can be used for the following applications

2 channel audio
Multi-room audio
Pools, spas, hot tubs rooms, etc.

Supplied with white grill cover.

The acive wall speakers work exactly the same way as the ceiling speakers. The right speaker has an integrated amplifier and IR receiver. The left speaker connects to the right speakers. the speakers are IP65 rated so can be used outside with no issues.

Metal back box for 6 1/2" round in-ceiling speaker.
To suit:
AC-640
AC-642 etc

Speaker Back boxes can be used to protect the speaker from insulation and high voltage wiring, as well as to keep the sound from traveling into adjoining rooms.

Short (low profile) Metal back box Can for 6 1/2" round in-ceiling speaker.
To suit:
AC-640
AC-642 etc

Speaker Back boxes can be used to protect the speaker from insulation and high voltage wiring, as well as to keep the sound from traveling into adjoining rooms.

This firehood can be used with any of the 6.5 inch ceiling speakers.

This is a dummy speaker pair that can be used if you are prewiring a property but not actually putting the speakers in. This allows the holes to be cut and the dummy speaker can be fitted to provide a clean finish.

The latest in Onkyo’s line of RI (Remote Interactive) Docks for the iPod links with your home entertainment system to get more out of your music, movies, TV shows, music videos, and video podcasts. The DS-A3 is equipped with component video output, to ensure greater quality and reliability for video playback. You also have the benefits found on earlier Docks: recharging capability; onscreen display for navigation and content selection; a dedicated remote control; and integrated operability through Onkyo’s RI system. Combining iPod versatility with Onkyo sound quality is a simple formula for pure enjoyment

This clever device allows an iPod to be used as a local source in an A-BUS audio system.

The Docking Station fits into a single American J back box and fits in line on the Cat5e cable from the A-BUS hub to the A-BUS amplified keypad or the Active A-BUS/DIRECT speakers.

The system is auto sensing so it will cut in the local iPod source as soon as audio starts to be played and will revert back again if the audio at the local source is stopped.

iPod not inluded.
right click for Spec Sheet . . .

This in wall docking station is designed to with all current versions of iPod excluding the shuffle.

The docking station mounts to a single gang American J box. A single Cat5e is used to connect to the output plat which also fixes to an American J back box. The output plate presents RCA phono for audio output, DC power input to power the system anc charge the iPod and an IR input for connection to an IR receiver at the output plate.

iPod not included.

There is also an built in IR Receiver at the docking station. The system can accept commands to play, pause, skip forward and skip back. HEX codes are available or you can use the Apple remote.
right click for spec sheet . . .